High-Torque Rotary Actuator Sizing Calculator & 2000 Series Guide

Estimate high torque rotary actuator peak/RMS torque and bearing moment, then compare real model ratings. Looking for 2000 series high torque rotary actuators? Identify the manufacturer and variant first.

Preliminary demand estimate

Output peak 41.7 Nm

Output RMS 28.3 Nm

Demand only; model ratings, thermal capacity and bearing life are unverified. All fields are required; defaults and presets are illustrative.

One positive-direction stroke with linear ramps, constant resisting torque and motor-energized dwell. Enter full-cycle data elsewhere for reversing axes.

1. Motion Kinematics & Stroke

[deg]

Angular displacement per index or operational stroke. Range: 1–36000 deg.

[rpm]

Maximum rotational velocity at the actuator output flange. Range: 0.1–600 rpm.

[s]

Time required to accelerate from standstill to peak speed. Range: 0.02–10 s.

[s]

Time required to brake from peak speed to standstill. Range: 0.02–10 s.

[s]

Stationary or holding duration before next movement cycle. Range: 0–60 s.

2. Load Inertia & Resistive Torques

[kg·m²]

Total inertia of payload, fixture, and turntable about rotation axis. Range: 0.001–50 kg·m².

[Nm]

Friction from external guide bearings, seals, and wiping seals. Range: 0–300 Nm.

[Nm]

Constant torque opposing this positive-direction stroke; same holding torque during dwell. Range: 0–1500 Nm.

3. Actuator Transmission & Thermal

[:1]

Actuator transmission speed reduction ratio. Range: 1–300 :1.

Mechanical efficiency of harmonic, cycloidal, or planetary gear train. Range: 0.4–0.98 .

[×10⁻⁴ kg·m²]

Internal servomotor rotor inertia (excluding gearhead). Range: 0.05–50 ×10⁻⁴ kg·m².

[×10⁻⁴ kg·m²]

Motor-referred gear inertia from supplier; 0 excludes it until known. Range: 0–1000 ×10⁻⁴ kg·m².

[°C]

Surrounding enclosure or ambient room temperature. Range: -20–75 °C.

4. Output Shaft External Bearing Loads

[N]

Overhung radial load acting perpendicular to output shaft. Range: 0–40000 N.

[mm]

Distance from mounting flange face to radial load point. Range: 0–1000 mm.

[N]

Thrust parallel to shaft axis; specify radial eccentricity separately. Range: 0–40000 N.

[mm]

Radial offset of axial force from shaft center; zero for centered thrust. Range: 0–1000 mm.

Demand estimate statusEstimate only

Calculated demand is ready for comparison with supplier ratings. No selected model has been validated.

Peak Output Torque (Tpeak)
41.7Nm

Accel: 41.7 Nm | Decel: 20.3 Nm

Continuous RMS Torque (Trms)
28.3Nm

Duty Cycle: 42.9%

Inertia Ratio (λ = JL/[R²Jm])
0.4:1

Lower screening ratio; verify drive limits

Output Tilting Moment (M)
187Nm

Applied moment; bearing capacity unverified

Motor-Side Peak / RMS
0.82 / 0.42Nm

Motor Speed: 3000 rpm

Reducer to compare (heuristic)
Strain Wave (Harmonic)

Thermal capacity: not evaluated

Normalized speed & signed output torque
Speed ω(t)Torque T(t)
Peak: 30 rpmt = 1.75s0s
Move: 0.75sDwell: 1.0sCycle: 1.75s

Trapezoidal stroke: accel 0.250s, cruise 0.250s, decel 0.250s. Curves use independent normalized scales; dashed torque is signed around the midline.

Assumptions & next step

  • Demand estimate only: no actuator, motor, drive or bearing ratings have been checked. Confirm torque-speed curves, peak duration, current and combined bearing loads with the supplier.
  • Gearhead input inertia is excluded (0 entered). Add supplier data before motor selection.

Compare motor peak/RMS at calculated motor speed, reducer duty/peak duration, and combined bearing loads with the selected model. Export this estimate for supplier review.

1. Decision rules before choosing hardware

Demand estimate to defensible selection
Model the complete motion and loads
Compare manufacturer curves and limits
Validate mounting, controls and duty on hardware

2. What does 2000 Series actually identify?

A documented match is 2G Engineering — 2000 Series Subsea Rotary Actuator ↗. Its 2000 Series includes High Speed and High Torque variants. This is a manufacturer-specific subsea product family, not evidence of a universal 2000 Nm rating, 2-inch frame or interchangeable industrial package.

2000 Series High Torque: manufacturer page snapshot, reviewed November 12, 2026
Published item2G High Torque variantDecision boundary
Continuous torque30 ft·lbf ≈ 40.7 NmFrom variant description; confirm duty and cooling
Peak torque50 ft·lbf ≈ 67.8 NmPeak duration and torque-speed curve require confirmation
Maximum speed9 rpm at 24 VDo not assume maximum torque and speed are simultaneous
Environment and constructionOil-filled, compensated subsea unitAn industrial joint needs separate environmental qualification
RJA drop-in equivalenceUnknown / not establishedNo verified matching model or interface comparison

Conversion uses 1 ft·lbf = 1.35581795 Nm. The same manufacturer page’s family summary mixes values from different variants and contains differing temperature/depth summaries. Use the variant description for orientation and obtain the current configuration datasheet before procurement. Ratings above are a source snapshot, not a live stock or compatibility claim.

For part-number and interface identification, see 2G Engineering — 2000RHT High Torque datasheet, Rev D, p. 1 ↗. Its 2000RHT drawing is Rev D, dated October 30, 2015. Confirm the revision for your serial number before using its dimensions or pinout.

3. Calculation method and reproducible assumptions

The solver models one positive-direction index followed by an energized holding dwell. Acceleration and deceleration are constant; friction and external resistance are nonnegative and fixed. The external torque also acts throughout the dwell. The return stroke, varying gravity, process transients and compliance are excluded. Oriental Motor — Acceleration Torque and RMS Torque ↗

Implemented equations (SI units)
QuantityMethodLimit
Velocity and rampsω = rpm × 2π/60; α = ωrequested / ramp timeShort strokes reduce achieved speed and ramp duration
Output phase torqueT = Jload × αsigned + Tfriction + Texternal; dwell = TexternalLoad inertia includes fixture and output-side moving mass
Motor phase torqueTm = g(T) + (Jmotor + Jgear,input) × R × αsignedg(T) = T/(Rη) for positive T; Tη/R for negative T during positive motion
Motor holding torqueTm,hold ≈ Texternal/(Rη)Conservative motoring-equivalent estimate; no self-locking or brake credit
RMS and peakRMS = √(Σ Ti²ti / Σ ti); peak = max |Ti|Calculated separately at output and motor; no safety factor added
Inertia screening ratioλ = Jload / (R² × Jmotor)Does not include gearhead inertia in this displayed load/rotor ratio

Efficiency is a fixed bidirectional approximation. Real efficiency varies with speed, torque and temperature; standstill holding does not follow a power-efficiency model exactly. Gearhead input inertia defaults to zero until known and is explicitly flagged. These assumptions can materially change motor demand.

Keep torque reference sides separate
Payload demand at output flange
Apply ratio and directional efficiency
Add motor and gear input acceleration torque

4. Compare demands with the right ratings

Required acceptance evidence — none is inferred from the calculator
CheckData neededAction when unknown
Motor peak / RMS / speedTorque-speed curve, peak time, voltage, cooling, current limitsRequest motor/drive sizing review
Reducer load and lifeRated duty, fatigue model, allowable peak and emergency torqueRun supplier equivalent-load and life calculation
Inertia and settlingDrive permissible inertia, stiffness and measured responseSimulate or bench-test the full mechanism
Bearing capacityRadial/axial loads, moment vector, preload, mounting and life targetUse the actual bearing selection method
Thermal capacityAmbient limits, mounting heat sink, winding and drive lossesObtain manufacturer derating curves

A computed estimate remains unqualified until these data are available. There is no universal 4500 rpm limit, 800 Nm bearing gate, 500% shock allowance or IEC-certified derating curve implemented here.

Request missing torque-speed curves and interface data

5. Reducer and integration tradeoffs

Architecture comparison — selection questions, not product ratings
OptionInvestigateTradeoff / alternative
Strain-waveBacklash, torsional stiffness, flexspline fatigue, hollow boreCheck repeated peaks and life at your load spectrum
CycloidalRated torque, rigidity, shock limits, output bearing arrangementCompare mass, housing and input-stage integration
Precision planetaryRatio stages, backlash, input speed, efficiencyCheck whether output support or feedback must be external
Direct drive / external supportMotor size, current, cooling and bearing supportMay remove gear backlash but change thermal and structural cost

The tool’s reducer suggestion uses simple internal thresholds (450 Nm peak, 600 Nm moment, or speed/ratio bands). These are comparison heuristics without manufacturer qualification. Obtain candidates across architectures when packaging, life or precision dominates. No RJA weight-saving or torque-density percentage is established here.

6. Thermal duty and energized holding

Motion duty percentage is moving time divided by stroke-plus-dwell time. A stationary motor can still carry external torque and produce winding heat. Extending a loaded dwell can therefore retain substantial motor RMS demand. Output RMS describes this load cycle; it is not a reducer fatigue-life model.

Ambient temperature is recorded for supplier review. The tool does not calculate a permissible continuous torque percentage. Insulation class alone does not determine housing cooling, gearbox temperature, drive limits or usable torque. Oriental Motor — Acceleration Torque and RMS Torque ↗

Thermal review inputs
Compute motor phase RMS including hold
Supply ambient, mounting and cooling data
Check the selected motor and drive thermal curves

7. Bearing loads and eccentricity

The screening moment is M = Fr × L + Fa × e, with distances converted from millimetres to metres. L is the axial overhang of the radial force from the bearing reference plane; e is the radial eccentricity of the axial force. Magnitudes are added as a worst-case aligned approximation. With centered axial thrust, e = 0 and its moment term is zero, but thrust still loads the bearing. THK — Cross-Roller Ring Structure and Features ↗

Bearing planeFrFaLe
Load geometry only; not a dimensional drawing or bearing capacity plot.

For example, Fr = 2000 N at L = 100 mm gives 200 Nm. A centered 1000 N thrust adds no moment; an eccentricity of 40 mm adds 40 Nm. Axial/radial capacity, moment vectors, combined equivalent load, mounting bolts, stiffness and bearing life remain separate checks.

8. Retrofit, control and environment checklist

Known / unknown before a replacement decision
InterfaceCollectCurrent evidence status
MechanicalPilot, bolt circle, shaft, flange, bore and permissible loadsUnknown until drawings are compared
Electrical / controlsSupply, pinout, current, protocol, feedback and brake logicNo fieldbus or encoder equivalence assumed
EnvironmentPressure, fluid, seal, corrosion, lubricant and connector specification2G subsea use does not qualify an industrial alternative
PrecisionBidirectional accuracy, repeatability, stiffness and thermal driftEncoder bit count is not installed positioning accuracy
Safety / serviceStopping behavior, brake duty, risk assessment and maintenance instructionsNo certification, lifetime or maintenance-free claim inferred

Output feedback can observe gearbox errors but cannot remove physical backlash or elasticity. Verify installed accuracy under actual load reversals. Request configuration-specific documentation for IP rating, functional safety and lubrication intervals.

9. Reproducible application examples

These four hypothetical cases use the exact preset values in the tool, default ambient 30°C, centered axial thrust and gearhead input inertia excluded. Select the matching preset to inspect all assumptions. Results below are generated by the same solver, not measured performance or catalogue ratings.

Preset outcomes — no safety margin or model approval
ExampleInputs: JL / R / strokeOutput peak / RMS (Nm)Motor peak / RMS (Nm)Action
Heavy industrial load (example)32.0 kg·m² / 160:1 / 180°437.4 / 221.43.87 / 1.83Add missing gear inertia; verify full cycle and ratings
Robotic Waist / Shoulder Joint (J1/J2)1.20 kg·m² / 101:1 / 90°113.8 / 92.91.89 / 1.22Add missing gear inertia; verify full cycle and ratings
High-Precision Rotary Table / Indexer0.65 kg·m² / 80:1 / 45°36.2 / 14.60.99 / 0.37Add missing gear inertia; verify full cycle and ratings
Heavy AGV / AMR Rotary Steer Drive0.40 kg·m² / 60:1 / 90°63.3 / 48.81.52 / 1.00Add missing gear inertia; verify full cycle and ratings

The heavy industrial example is not a 2G rating. The shoulder example uses constant external torque for a single stroke; a real shoulder requires angle-dependent gravity and its return trajectory. The table example needs precision/settling validation; the steering example needs tire friction and shock measurements.

High torque rotary actuator calculator showing the fixed default example’s output peak and RMS demand with rating limitations
Original software execution captured November 12, 2026. Reproduce with Reset example; all motion, load and transmission inputs are shown in the calculator above. This is a browser result, not a hardware test, customer case study or manufacturer rating.

10. Misuse, cost and application risks

Misuse: partial cycle

Ignoring reversal, variable gravity or stops may understate demand. Supply a signed full-cycle torque/speed trace before motor and brake selection.

Cost: interfaces and validation

Budget for adapters, external support, drives, cables, cooling and test work alongside actuator price. Ask for a configuration-specific quotation.

Mismatch: subsea versus factory

A torque match does not address hydrostatic pressure, corrosion or sealing. Retain the qualified subsea unit or commission environmental qualification of the alternative.

If supplier data are unavailable, export the estimate as a requirements brief and request the missing curves and drawings. A product recommendation remains pending; numerical output alone does not resolve that gap.

11. Sources, review date and evidence boundaries

Published by Robot Joint Actuator. Guide first published November 12, 2026. Public sources reviewed . This is a documentation review, not empirical calibration, certification or test validation. Source pages may change; resolve the 2G family-summary inconsistencies with the supplier before purchase.

The tool equations and hypothetical scenarios are disclosed above. Architecture thresholds, constant efficiency and inertia screening bands are internal approximations. Unknown product ratings, safety evidence and retrofit equivalence remain explicitly unconfirmed.

12. Engineering FAQ and next steps

Identity & replacement

Does 2000 Series mean a 2000 Nm rotary actuator?

No. A verified example is the 2G Engineering 2000 Series subsea family. Series numbers are manufacturer identifiers; request the full part number and torque units. This page does not establish a universal 2000 Nm or 2-inch standard.

Is the industrial preset a 2G 2000 Series model?

No. Every tool preset is hypothetical application data. Gear ratio, rotor inertia and external loads are editable assumptions, not a manufacturer model database.

Can an RJA joint replace a subsea 2000 Series actuator?

Compatibility is unconfirmed. Pressure compensation, sealing, corrosion, connectors, controls, shaft loads and torque-speed duty must all be reviewed. A dry industrial joint is not a qualified subsea replacement.

Can I assume peak torque is available at maximum speed?

No. Separate catalogue maxima may describe different operating points. Obtain the torque-speed curve, permitted peak duration, voltage and thermal conditions for the exact variant.

Calculation & inputs

What does load inertia include?

Enter payload, fixture and all moving output-side components about this axis. Enter supplier motor-referred gearhead inertia separately. The zero gearhead default excludes an unknown quantity and is called out in the results.

What happens if the stroke is too short to reach requested speed?

The tool uses a triangular velocity profile at the entered acceleration rates. It reduces achieved speed and both ramp durations; the chart and results show effective rather than requested speed.

Why does motor RMS differ from output RMS divided by ratio?

Motor and gearhead input inertia add acceleration torque and braking torque in their respective phases. Motor RMS is integrated from those signed phase torques, including the holding dwell.

Can I calculate a reversing shoulder joint here?

Only a single positive stroke with constant resisting torque is modeled. A reversing joint needs both directions and angle-dependent gravity/inertia over the complete cycle in a multi-segment sizing model.

Limits & interpretation

Does a low inertia ratio prove the servo is stable?

No. The 5:1 and 10:1 bands are early screening heuristics. Consult the selected drive’s permissible inertia and validate stiffness, resonance, tuning and settling time.

Does centered axial thrust create an overturning moment?

No. The axial moment term is axial force times its radial eccentricity. Centered thrust has zero eccentricity but still loads the bearing and must be checked with radial and moment loads together.

Does the tool calculate thermal derating?

No. Ambient temperature is recorded and flagged for review outside the reference range. Continuous capacity requires manufacturer curves, mounting, cooling, winding and drive data; there is no universal derating percentage here.

Does the suggested reducer identify a matching product?

No. It is a comparison starting point based on simple demand heuristics. Torque alone cannot choose architecture, bearing size, service life or part number.

Validation & next steps

Does output RMS prove gearbox life?

No. RMS is useful for motor thermal screening under stated assumptions. Gearbox life may use a different equivalent torque exponent, speed weighting, shock factors and fatigue model supplied by the reducer manufacturer.

Are emergency stops and brakes included?

No. Determine stopping time, reflected kinetic energy, external torque, regeneration capacity and brake engagement behavior separately. Check the specific brake and reducer emergency ratings; a holding brake may not be a service brake.

What if my inputs are missing or I cannot copy?

Invalid fields show recovery guidance and suppress numeric results. Reset an example or ask for input help. If clipboard access fails, the sizing text opens for manual selection and copying.

What should I send with an engineering review request?

Send the exported demand estimate, full cycle including return and stops, model/nameplate, torque-speed curves, flange drawing, force application points, voltage, cooling and environment. Response time, compatibility and pricing require confirmation.

Return to the calculator to export your requirements, then attach the full cycle and interface drawings for an engineering review.